i-Socket Autoswitch 110V / 15 Amp
i-Socket Autoswitch 110V / 15 Amp Image

I-Socket Autoswitch 110 Volt / 15 Amps

$36.95 $39.95
Item #: DG11015


Product Description


The Intelligent i-Socket Autoswitch from DGC Products is a patented automatic vacuum switch that uses an on-Board Micro-Controller which is programmed to monitor and control the in-rush of current when two large motors try to power-up at the same time. Thus, eliminating an overload on the circuit breaker.

i-Socket is the ONLY intelligent switch that can control the in-rush of current on startup to eliminate circuit overload with a 7 second delay off.

  • Prevents circuit overload with auto turn on vacuum delay
  • Automatically delays vacuum turn-off by 7 seconds so you can walk away
  • Reduces airborne toxin that can lead to many health problems
  • Runs the vacuum only when you are working so you save time and electricity
  • Reduces work area noise by running the vacuum only when you use your tool

Specifications:
  • Dimensions: 2" x 4" x 3"
  • Finish: Black textured
  • Case: Durable UL-rated 94V, ABS plastic
  • Outlet required: Standard 15 Amp, 120 VAC, 60 Hz outlet
  • Power rating: 15 Amp, 120 VAC, 60 Hz
  • Input connection: 3 prong (grounded) male
  • Tool outlet connections: 2 or 3 prong plugs
  • Tool input: Miter saw, Table saw, Router, Planer, Sander or other cutting and sanding tools
  • Vacuum input: Wet/Dry Vacuum, Dust Collectors or Power Feed
  • Electronics: A software imbedded microcontroller controls the in rush of current when the motor starts up to help eliminate overload of the circuit. Once the tool stops, it provides power to the vacuum for seven seconds to clean out the inlet pipe. It shuts off the vacuum and sits in a ready state for the next use of the tool.

FAQ:
  • Can I use the i-Socket AutoSwitch with an extension cord?
    Yes. Use a 15 amp, grounded (3-prong) cord.
  • Why does the vacuum stay on?
    Check the power cords. The TOOL and VAC inputs may be reversed.
  • What is the warranty on my i-Socket AutoSwitch?
    The i-socket AutoSwitch is warranted for 90-days against manufactures defects. DGC Products, Inc reserves the rights to refund or replace any product found defective within the warranty period.
  • Can I connect multiple chop saws to one i-Socket AutoSwitch and Vac system?
    Yes, use a power strip to link all preset angled chop saws. NOTE: Only one saw at a time can be triggered.
  • What is the Actuation Threshold?
    The actuation threshold is the minimum amount of current that needs to flow through the primary/TOOL outlet before the microprocessor turns on the secondary/VAC outlet. This current level is set to about 0.7 amps, which is roughly 85 watts at 120V).


GTIN: 

 

Items of Interest

Dust Collection Hose Grounding Kit
Dust Collection Hose Grounding Kit
Item #: BH19250
$14.95
Jet RF Remote Control / Dust Collector
Jet Rf Remote Control / Dust Collector
Item #: J708636C
$89.99 $99.99
Long Ranger III Remote 110V Starter
Long Ranger Iii Remote 110V Starter
Item #: PI11030
$69.95
Floor Sweep W/ 4" Port  21"
Floor Sweep W/ 4" Port 21"
Item #: WK10030
$7.95
3" x 10' Hose (Black)
3" X 10' Hose (Black)
Item #: WK10280
$16.95
4" x 10' Dust Hose (Black)
4" X 10' Dust Hose (Black)
Item #: WK10310
$20.95
Dust Collection Basics Book
Dust Collection Basics Book
Item #: WK10500
$7.95
4" Wire Hose Clamps
4" Wire Hose Clamps
Item #: WK13170
$0.99
5 Gallon Separator Lid
5 Gallon Separator Lid
Item #: WK20490
$16.95
Hose Hanger 4-1/4"
Hose Hanger 4-1/4"
Item #: WK21070
$0.99
Dust Collection Pick Up Accessories Kit
Dust Collection Pick Up Accessories Kit
Item #: WK37560
$69.95
Jet HD Universal Mobile Base
Jet Hd Universal Mobile Base
Item #: DS708118
$80.99 $89.99